Specifications

This chapter discusses power requirements, dimensions, and other specifications of the UX300-series card reader.

UX300 Models

The following table shows the various models and specifications of UX300-series units.

Model Name	Part Number	Specifications
UX300-Standard	M159-300-000-WWA M159-300-000-WWA-B M159-300-100-WWA-B	UX300-Standard, Mag/Chip Reader and controller interface: 12 V in, LAN, RS232, USB-Slave, USB-Master, NFC-Antenna.
UX300-MDB	M159-300-010-WWA-B	UX300-MDB; UX300-Standard plus following interface: MDB, 4xUSB-Master, 2xRS232 Powered.
UX300-PSTN	M159-300-020-WWA-B	UX300-PSTN; UX300-Standard plus following interface: MDB, 4xUSB-Master, 1xRS232 Powered, PSN.
UX300-ISDN	M159-300-030-WWA-B	UX300-ISDN; UX300-Standard plus following interface: MDB, 4xUSB-Master, 1xRS232 Powered, ISDN.
UX300-GPRS	M159-300-040-WWA-B	UX300-GPRS; UX300-Standard plus following interface: MDB, 4xUSB-Master, 1xRS232 Powered, GPRS.
UX300-Petrol	M159-300-050-WWA-B	UX300-Petrol; UX300-Standard plus following interface: 24V, 4xUSB-Master, 2xRS232 Powered, RS485.
UX300-LAN	M159-300-060-WWA-B	UX300-LAN; UX300-Standard plus following interface: MDB, 4xUSB-Master, 2xRS232 Powered, 2nd LAN.
UX300-WPWR	M159-300-070-WWA-C	UX300-WPWR; UX300-Standard plus following Interface; 9 to 43 V Power In; PCI 3.1 and UKCC compliant.

Unit Power Requirements

UX300-Standard

• Operation voltage: 9 V DC to 12 V DC
• Idle Power: 2 W
• Typical Power: 3 W (CTLS read), 4W (UX100 display heater), 0.5W (UX100/110), 5W (RS232-vout)
• Sleep Mode: Approximately 30 to 50 mW, wakeup time 7 sec.

UX300-MDB, UX300-PSTN, UX300-ISDN, UX300-GPRS, UX300-LAN, UX300-WPWR

• Operation voltage: 9 V DC to 43 V DC
• Idle Power: 4 W
• Typical Power: 3 W (CTLS read), 4 W (UX100 display heater), 0.5 W (UX100/110), 5 W (RS232-vout),
• 10W(USB-Master), 3 W (GPRS connect)
• Sleep Mode: Approximately 30 to 50 mW, wakeup time 7 sec.

UX300-Petrol

• Operation voltage: 24 V DC
• Idle Power: 4 W
• Typical Power: 3 W (CTLS read), 4 W (UX100 display heater), 0.5 W (UX100/110), 5 W (RS232-vout),
• 10W(USB-Master), 70 W (printer)
• Sleep Mode: Approximately 30 to 50 mW, wakeup time 7 sec.

Temperature

• Operating temperature:

  • -20°C to 70°C (-4°F to 158°F) Standard unit
  • -20°C to 65°C (-4°F to 149°F) MDB, LAN, Petrol units
  • 0°C to 65°C (32°F to 149°F) PSTN, ISDN units
• Storage temperature: -25°C to 70°C (-13°F to 158°F)
• Power Supply rated for indoor use only: 12 V DC 3.3A, operating temperature 0°C to 40°C (32°F to 104°F)
• Power Supply rated for outdoor use: 24 V, DC 3.75 A up to 40°C (DC 2.5 A up to 60°C), operating temperature -25°C to 60°C
• Relative humidity: 5% to 90% RH non-condensing

If this device is to be used in the Nordic countries, or in any environment where the temperature range exceeds the product's operating temperature, it is the responsibility of the integrators to ensure that the ambient environment is controlled in such a way to ensure that the product operates within the specified temperature range.

External Dimensions

• Height: 72 mm (2.83 in)
• Width: 96 mm (3.78 in)
• Depth: 150 mm (5.9 in)

Weight

• Unit weight: 750 g (26.46 oz)

Memory

• 128 MB DDRAM
• 256 MB NAND-Flash

Magnetic Stripe Card

• Triple-track

Smart Card Reader

• Non-sliding
• Card conserving plated landing contacts

SAM Requirements

• 2 SAM slots

Peripheral Ports

• Consistent ports:

  • Power
  • Powered USB Type A for UX PIN pads (host)
  • USB Type B (client)
  • COM1 (powered)
  • ETH (LAN) connection with 2 colored LEDs for link state and speed indication
  • Analog RF CTLS antenna connector to the UX400 CTLS unit
  • 8-PIN to RJ45 connector to UX400 CTLS antenna unit
• Model-dependent cable connection board:

  • 4 Powered USB Type A
  • MDB
  • Additional COM powered ports
  • GPRS antenna
  • ISDN
  • PSTN
  • RS-485
  • An additional ETH connection with 2 colored LEDs for link state and speed indication
  • Printer COM

Communication

• COM: Up to 115200 bps, HW RTS/CTS handshake
• MDB: 9600 bps fix, 9E1
• RS-485: Up to 115200 bps, half duplex

Display

• 3 status LEDs on the front (payment application controlled)